How to Run Wire Through Walls

One of the best reasons for mounting your new flat panel TV on the wall is the sleek and stylish look that it gives the entire room. Just look at how it complements our fireplace. What’s not so sleek and stylish, however, are all the cords and cables dangling from below the TV, running across the mantle and down the wall. We’re going to tie into an existing electrical outlet and run new electrical wire and TV cables up through the wall.

Once you finish the steps to this video, move on to part two: Adding an Electrical Outlet: TV hook-up.

**WARNING**
If you’re unsure about working with electricity, you should call a licensed electrician to do the work. But if you’re ready to give it a try, let’s go ahead and get started.

Tools

Steps

  1. How to Run Wire Through Walls (part 1) - Step 1

    Open the breaker box and turn off the electricity to the area you’ll be working in. Use a work light if you need light.

  2. How to Run Wire Through Walls (part 1) - Step 2

    Make sure the power is off near the outlet you’ll be working with using a voltage tester.

  3. How to Run Wire Through Walls (part 1) - Step 3

    Remove all wall-mounted items from the area that you will be running the wires.

  4. How to Run Wire Through Walls (part 1) - Step 4

    Locate the studs and plumbing in the wall using a stud finder. Mark these locations with a pencil.

  5. How to Run Wire Through Walls (part 1) - Step 5

    Measure and draw the lines where you want to cut out the drywall. Then cut through with a drywall saw. Save the cut piece so you can place it back in after the project is complete.

  6. How to Run Wire Through Walls (part 1) - Step 6

    Cut a hole through each stud using a right-angle saw and a 1-1/2″ hole saw. This will create a pathway for our plastic conduit tubing.

  7. How to Run Wire Through Walls (part 1) - Step 7

    For the electrical cable, we’ll drill a hole 6” above using this 3/4”spade bit.

  8. How to Run Wire Through Walls (part 1) - Step 8

    cut a hole for the new electrical box. Also cut a hole near the floor outlet to make the job of pushing the wire through easier.

  9. How to Run Wire Through Walls (part 1) - Step 9

    Start pushing the wire through the highest point in the wall and work your way down. Feed the wire and cables through the holes until everything is in place.


Read Video Transcript

One of the best reasons for mounting your new flat panel TV on the wall is the sleek and stylish look that it gives the entire room. Just look at how it complements our fireplace. What’s not so sleek and stylish, however, are all the cords and cables dangling from below the TV, running across the mantle and down the wall. What an eyesore. To hide them, we’re going to run these wires through the wall and up to a point behind the TV where they will be out of sight, hidden from our view.

Today, in this first of a two-part series on wiring a wall-mounted flat panel TV, we’re going to tie into an existing electrical outlet and run new electrical wire and TV cables up through the wall. Then we’ll make a 90-degree turn and route the wiring through several studs before we reach our destination behind the TV. In the next video, we’ll install an electrical box and receptacles and connect the wires and cables. Now before we begin, if you have any hesitation about working with electricity or hooking up electrical components, it’s best to call a licensed electrician to do the work. But if you’re ready to raise your DIY electrical skills a few notches, then let’s get started.

The first step when working with electricity is always to turn off the power feeding the circuit you’re working on at the breaker box. You might need to set up a work light plugged into an outlet on a different circuit. Check the outlet with a tester before starting to make sure it’s safe to examine the existing outlet that we’ll tie into. Lucky for us it’s at the end of a circuit, which will make wiring much easier. This is evident by the single wire cable entering the electrical box. Common types of cable for residential electrical work include 14/2 and 12/2 non-metallic sheathed cable. We’ll use 12/2 because it’s the same gauge as the existing wire supplying the box. The first number represents the gauge of the wire, where the lower the number, the thicker the wire. The second is the number of wires inside the cable. This cable also includes a ground wire. We’ll also take this opportunity to install double-gang boxes at both ends to accommodate both the electrical outlet as well as our TV cable and wiring. But more on that in the next video.

After recruiting some help to remove the TV, and taking down anything else in the way, we’ll use this stud finder to locate the wall studs and any other obstacles blocking the path. After investigation, it looks like there are two wall studs we’ll have to drill through en route to our final destination. We also made sure there weren’t any plumbing or electrical lines in the way. We’ve marked everything with a pencil on the wall so we know exactly where all framing members are located. Now, it’s time to use our drywall saw and cut some strategic holes in our drywall to provide room to drill holes through the wall studs so we can run our wiring and cable.

The hole we’ll cut starts directly above the existing outlet and ends near the new outlet that will be placed above our TV bracket. We’ll cut a rectangular strip across the two studs bays and the studs that we’ll be drilling through, making sure to stop the cut at the last stud. This rectangular strip should be about 8”high so we can keep our line and low-voltage wiring at least 6” apart. This will help avoid any possible electromagnetic interference that might occur between the two wires.

Using a drywall saw, we’ll punch a starter hole and cut carefully so we can reuse the piece during the drywall repair phase of this project. Directly over the studs, we’ll use a blade knife. Using our level as a straightedge for our cuts will help. When we removed the drywall, we found that we had two studs side by side, which goes to show that you never really know what you’ll find when you cut away the drywall. In our case it won’t be a problem.

Now we’ll use the right-angle drill that we rented from our local independent home improvement retailer and a 1-1/2” hole saw to drill a hole directly through the center of each stud. This will create a pathway for our plastic conduit tubing. For the 12/2 electrical cable, we’ll drill a hole 6” above using this 3/4”spade bit. Be sure to drill these holes as straight and level as possible so the wires or conduit won’t snag as we pull it through. For more on drilling through studs, see our list of frequently asked questions for this video.

Now we’ll cut a hole for the new electrical box on the other side of the last stud we drilled through, using the electrical box as a template. We’ll also cut an access hole to make fishing the wires and cables easier. We’ll premeasure the 12/2 cable so we can see how far we need to feed it down the wall.

TV Wall Hook-up (Part 1)

At this point we’ll pull the cables through the holes in the drywall we just created. We’ll start at our highest opening on the wall and push the cable down through the stud bay to the hole that will house our new electrical box. We’ll repeat the same process for our plastic conduit, which we’ve pre-loaded with both our HDMI and coaxial cables, taped together at the ends so they won’t slip down into the conduit. If we hit any snags, we’ll use this fish tape to help pull the cable or conduit on through. Now we’ll head across the wall, first with our electrical cable, then with the plastic conduit.

There you have it. We’ve got our wiring run and in place. In the next video, we’ll install an electrical box and the needed receptacles to house and connect our electrical wires and TV cables.

Close Transcript

Send to Kindle


Read more from: How-To Videos > Electrical

Back to top

72 responses to “How to Run Wire Through Walls”

  1. BJ says:

    this was so much help, thank you, thank you, thank you!!

  2. eric says:

    love how you forgot to video the patchwork required afterwards 🙂

  3. Roberto says:

    I Never leave comments, but you just safe my life with this video.
    Thank You 🙂

  4. NAHOMY ATIAS SMITH says:

    I spent hours looking for a video like this! I need to do exactly the samething for my tv… btw, how can u keep your nails like that while working with wires, outlets and drywall? mine are just ruined lol Thank you!!!

  5. Joe Blow says:

    It is pretty easy to poke holes in the walls to run wires but who repairs the drywall, matches the existing texturing on the drywall, finds correctly matching paint, and repaints everything? Poking holes in the wall is the easy part.

  6. Paul Denado says:

    Roberto, If this video saved your life, you are obviously short on common sense.

  7. Pauls a Dick says:

    That may be so Paul, but you’re an arsehole.

  8. Rick Smith says:

    Here’s the best way to patch the drywall opening after running your wires. Cut a piece of drywall that’s four inches wider and four inches taller than the hole size. Then cut out the size that fits but leave two inches of paper on all four sides. When you put the piece in the hole it can’t fall in because you have the extra paper around the entire edge of that piece are you following me on this so far. Ok now put some drywall mud around the edges of the hole put the piece in the hole and make sure you push the excess mud out from under the paper so it’s not humped up. Let that dry and then put at least two more thin coats of mud around the patch feathing them out. If you do it right you will never know the hole was there. Anyway hope that helps

  9. If you are looking for one of the best website for file explorer windows 10 so here it is one of the best website which will help you to learn new things in which you may be facing problems.

  10. Patty says:

    This article interested me very much. You described it great. Certainly I will be looking at your blog more often.

  11. windows 10 says:

    I enjoy reading your blog. It’s inspriring. Hope that you release more blog like this

  12. Here if you want the latest apps for your device go with play store for free.

  13. Bernard Summers says:

    Hi can I chase a lighting cable down one side and fit the switch on the other side of the wall ?

  14. Wendy says:

    Thanks for another great electrical post! I have a room full of wallplugs that need switching out to white.

  15. thanks for providing usefu information on How to Run Wire Through Walls

  16. mac says:

    very nice article I am subscribing to your blog

  17. jmaes says:

    very nice article I am subscribing to your blog

  18. happy wheels says:

    The information is very special, I will have to follow you, the information you bring is very real, reflecting correctly and objectively, it is very useful for society to grow together.

Leave a Reply

Your email address will not be published. Required fields are marked *

Current month ye@r day *