Garage Floor Options – Epoxy Finish (Part 1)

Garage floors can take a beating, but an epoxy finish to your garage floor will help transform the space from dark and dingy into colorful and cool. In part one of this two-part video series, we’ll show you how prep your garage floor the right way to get it ready for a fresh coat.

Once you are finished with the steps in this video, check out part 2 of this project.

Tools

Steps

  1. Garage Floor Options - Epoxy Finish (Part 1) - Step 1

    Move everything off the garage floor.

  2. Garage Floor Options - Epoxy Finish (Part 1) - Step 2

    Scrape off debris.

  3. Garage Floor Options - Epoxy Finish (Part 1) - Step 3

    Sweep the floor.

  4. Garage Floor Options - Epoxy Finish (Part 1) - Step 4

    Wash off the entire surface with a hose. If the water beads up, that means there is sealer that needs to be removed.

  5. Garage Floor Options - Epoxy Finish (Part 1) - Step 5

    If there is no sealant present, vacuum out cracks.

  6. Garage Floor Options - Epoxy Finish (Part 1) - Step 6

    Fill cracks with some crack filler and spread evenly with a putty knife.

  7. Garage Floor Options - Epoxy Finish (Part 1) - Step 7

    For holes, chisel out and vacuum dust away.

  8. Garage Floor Options - Epoxy Finish (Part 1) - Step 8

    Fill holes with concrete patch and a putty knife.

  9. Garage Floor Options - Epoxy Finish (Part 1) - Step 9

    Tape down plastic for 24 hours to test for moisture seeping up through the floor.

  10. Garage Floor Options - Epoxy Finish (Part 1) - Step 10

    Scrub the floor with cleaner, rinse with water and let dry.


Read Video Transcript

Refinishing your garage floor with a fresh coat of paint is something anyone can do to freshen up and prolong the life of your garage floor surface for years to come. But to make it last, you should consider an epoxy floor finish from your local independent home improvement retailer. Not only will it last longer than a traditional finish, it will make a lasting impression on anyone who sees it.

In the first episode, we’re going to show you how to properly prepare the concrete surface of your garage. Then, in the second part, we’ll demonstrate the proper application techniques to ensure your new finish lasts for years to come. So let’s get started.

As with most painting projects, surface preparation is key to getting a good finish, especially for an older garage floor like the one you see here. For the epoxy paint to adhere properly, it must be clean. First, we’ll completely remove everything from the garage. Then we’ll scrape off any debris, like this drywall compound and dried on glue.

Then we’ll sweep the floor completely to remove dirt, dust and any other debris, such as sawdust.

Once the floor has been swept, now it’s time to hose the entire surface off. After hosing off the surface, we’ll check for beading water, which indicates that the surface has been sealed. The manufacturer of this product states that any sealer present must first be removed for the product to work correctly. With no beading water present, it looks like we’re in good shape and can proceed. But first we have to let the area dry completely. These floor fans should help speed the drying.

Now that our floor is dry, it’s time to check for any cracks or spalling in the concrete that we need to repair. Looks like we have some work to do. For the cracks, we have some liquid filler we simply pour into the crack. However, before we do that we have to clean the crack out completely with a putty knife or an old 5-in-1 painters’ tool like this one. Now we’ll vacuum out the remaining dust from the crack, and fill it with the crack filler using a putty knife to level off the beads.

Areas like this hole and this cracked area that is spalling will require some additional attention. To fill this type of hole, we first need to back chisel the bottom of the hole to give the filler something to hold onto. We can do this with a hammer and a small cold chisel. Notice how I’m back chiseling the bottom of the hole to create a notch for the patch to grab.

After we’re done, we’ll vacuum out the hole and it’s ready for the patching material. Use a putty knife to install patch material and let it dry according to the manufacturer’s instructions.

While we’re waiting for our patches to cure, we can do some additional investigative work to check for moisture problems in the concrete. According to the manufacturer, if your concrete is new poured, you have to wait 60 days for the concrete to cure before you can apply this product. To check for moisture problems in our floor, we’ll tape down this 2’x2’ piece of plastic wrap and let it sit for 24 hours, which is how long it will take our concrete patches to completely cure.

If any water droplets appear on the patch after 24 hours, it indicates that the concrete has moisture problems that need to be addressed first before proceeding. Looks like we’re good to proceed.

The next step is to scrub the floor using this product to etch the surface of the concrete. This will make it so the epoxy paint will adhere better. Following the manufacturer’s instructions, we’ll apply this product to the floor and use this stiff bristle brush to completely scrub the floor, concentrating on heavily stained areas.

The last bit of preparation is to completely rinse the floor with the garden hose. Let it dry and check for any remaining residue by wiping your finger over the floor to check for dust. If any remains rinse again.

There you have it. Now we’ll let our floor dry overnight and be ready to apply our coating tomorrow.

If you have questions about this or any other home improvement project, be sure to read our list of Frequently Asked Questions for this video. And be sure to print out our Project Instructions, which includes a Tools and Materials checklist, before visiting your local independent home improvement retailer. That’s where you’ll find all the products and helpful advice to complete your project. If you’re not sure where to find your local store, check out our Store Locator.

Good luck with your project and thanks for watching.

Close Transcript

Send to Kindle


Read more from: How-To Videos > Garage & Workshop

Back to top

25 responses to “Garage Floor Options – Epoxy Finish (Part 1)”

  1. GIF Images says:

    so I just wanted to give a quick shout-out and say I genuinely enjoy reading your articles. Your blog provided us useful information. You have done an outstanding job.

  2. Thomas Labriola says:

    Thanks to the author for this guide. Personally, I also think that an epoxy finish for your garage floor is the best option. Many do not even think about what the optimal coverage for a garage should be. I advice you to post this article in Instagram so that many interested people can see it. And you can always use the services of https://viplikes.net/ to increase number of followers.

  3. Hii,
    This is Great Post.. for me, Thanks for sharing with us!!
    Buy Real Facebook Live Stream Views

  4. run 3 says:

    We are quite grateful that you spent some of your time and effort to clarify all of this for us. The kind of blog content that you are referring to has been of great assistance to me.

  5. Makayla Florance says:

    Basis of the garage workshop are done for the top of the reforms for the citizens. The notion of the USDOT Permits is fit for the success. The management is led for the terms for the width for the supportive means for the future aims.

Leave a Reply

Your email address will not be published. Required fields are marked *

Current month ye@r day *