How to Run Wire Through Walls

One of the best reasons for mounting your new flat panel TV on the wall is the sleek and stylish look that it gives the entire room. Just look at how it complements our fireplace. What’s not so sleek and stylish, however, are all the cords and cables dangling from below the TV, running across the mantle and down the wall. We’re going to tie into an existing electrical outlet and run new electrical wire and TV cables up through the wall.

Once you finish the steps to this video, move on to part two: Adding an Electrical Outlet: TV hook-up.

**WARNING**
If you’re unsure about working with electricity, you should call a licensed electrician to do the work. But if you’re ready to give it a try, let’s go ahead and get started.

Tools

Steps

  1. How to Run Wire Through Walls (part 1) - Step 1

    Open the breaker box and turn off the electricity to the area you’ll be working in. Use a work light if you need light.

  2. How to Run Wire Through Walls (part 1) - Step 2

    Make sure the power is off near the outlet you’ll be working with using a voltage tester.

  3. How to Run Wire Through Walls (part 1) - Step 3

    Remove all wall-mounted items from the area that you will be running the wires.

  4. How to Run Wire Through Walls (part 1) - Step 4

    Locate the studs and plumbing in the wall using a stud finder. Mark these locations with a pencil.

  5. How to Run Wire Through Walls (part 1) - Step 5

    Measure and draw the lines where you want to cut out the drywall. Then cut through with a drywall saw. Save the cut piece so you can place it back in after the project is complete.

  6. How to Run Wire Through Walls (part 1) - Step 6

    Cut a hole through each stud using a right-angle saw and a 1-1/2″ hole saw. This will create a pathway for our plastic conduit tubing.

  7. How to Run Wire Through Walls (part 1) - Step 7

    For the electrical cable, we’ll drill a hole 6” above using this 3/4”spade bit.

  8. How to Run Wire Through Walls (part 1) - Step 8

    cut a hole for the new electrical box. Also cut a hole near the floor outlet to make the job of pushing the wire through easier.

  9. How to Run Wire Through Walls (part 1) - Step 9

    Start pushing the wire through the highest point in the wall and work your way down. Feed the wire and cables through the holes until everything is in place.


Read Video Transcript

One of the best reasons for mounting your new flat panel TV on the wall is the sleek and stylish look that it gives the entire room. Just look at how it complements our fireplace. What’s not so sleek and stylish, however, are all the cords and cables dangling from below the TV, running across the mantle and down the wall. What an eyesore. To hide them, we’re going to run these wires through the wall and up to a point behind the TV where they will be out of sight, hidden from our view.

Today, in this first of a two-part series on wiring a wall-mounted flat panel TV, we’re going to tie into an existing electrical outlet and run new electrical wire and TV cables up through the wall. Then we’ll make a 90-degree turn and route the wiring through several studs before we reach our destination behind the TV. In the next video, we’ll install an electrical box and receptacles and connect the wires and cables. Now before we begin, if you have any hesitation about working with electricity or hooking up electrical components, it’s best to call a licensed electrician to do the work. But if you’re ready to raise your DIY electrical skills a few notches, then let’s get started.

The first step when working with electricity is always to turn off the power feeding the circuit you’re working on at the breaker box. You might need to set up a work light plugged into an outlet on a different circuit. Check the outlet with a tester before starting to make sure it’s safe to examine the existing outlet that we’ll tie into. Lucky for us it’s at the end of a circuit, which will make wiring much easier. This is evident by the single wire cable entering the electrical box. Common types of cable for residential electrical work include 14/2 and 12/2 non-metallic sheathed cable. We’ll use 12/2 because it’s the same gauge as the existing wire supplying the box. The first number represents the gauge of the wire, where the lower the number, the thicker the wire. The second is the number of wires inside the cable. This cable also includes a ground wire. We’ll also take this opportunity to install double-gang boxes at both ends to accommodate both the electrical outlet as well as our TV cable and wiring. But more on that in the next video.

After recruiting some help to remove the TV, and taking down anything else in the way, we’ll use this stud finder to locate the wall studs and any other obstacles blocking the path. After investigation, it looks like there are two wall studs we’ll have to drill through en route to our final destination. We also made sure there weren’t any plumbing or electrical lines in the way. We’ve marked everything with a pencil on the wall so we know exactly where all framing members are located. Now, it’s time to use our drywall saw and cut some strategic holes in our drywall to provide room to drill holes through the wall studs so we can run our wiring and cable.

The hole we’ll cut starts directly above the existing outlet and ends near the new outlet that will be placed above our TV bracket. We’ll cut a rectangular strip across the two studs bays and the studs that we’ll be drilling through, making sure to stop the cut at the last stud. This rectangular strip should be about 8”high so we can keep our line and low-voltage wiring at least 6” apart. This will help avoid any possible electromagnetic interference that might occur between the two wires.

Using a drywall saw, we’ll punch a starter hole and cut carefully so we can reuse the piece during the drywall repair phase of this project. Directly over the studs, we’ll use a blade knife. Using our level as a straightedge for our cuts will help. When we removed the drywall, we found that we had two studs side by side, which goes to show that you never really know what you’ll find when you cut away the drywall. In our case it won’t be a problem.

Now we’ll use the right-angle drill that we rented from our local independent home improvement retailer and a 1-1/2” hole saw to drill a hole directly through the center of each stud. This will create a pathway for our plastic conduit tubing. For the 12/2 electrical cable, we’ll drill a hole 6” above using this 3/4”spade bit. Be sure to drill these holes as straight and level as possible so the wires or conduit won’t snag as we pull it through. For more on drilling through studs, see our list of frequently asked questions for this video.

Now we’ll cut a hole for the new electrical box on the other side of the last stud we drilled through, using the electrical box as a template. We’ll also cut an access hole to make fishing the wires and cables easier. We’ll premeasure the 12/2 cable so we can see how far we need to feed it down the wall.

TV Wall Hook-up (Part 1)

At this point we’ll pull the cables through the holes in the drywall we just created. We’ll start at our highest opening on the wall and push the cable down through the stud bay to the hole that will house our new electrical box. We’ll repeat the same process for our plastic conduit, which we’ve pre-loaded with both our HDMI and coaxial cables, taped together at the ends so they won’t slip down into the conduit. If we hit any snags, we’ll use this fish tape to help pull the cable or conduit on through. Now we’ll head across the wall, first with our electrical cable, then with the plastic conduit.

There you have it. We’ve got our wiring run and in place. In the next video, we’ll install an electrical box and the needed receptacles to house and connect our electrical wires and TV cables.

Close Transcript

Send to Kindle


Read more from: How-To Videos > Electrical

Back to top

72 responses to “How to Run Wire Through Walls”

  1. JamesOneil says:

    I recently decided to take the DIY route for PPF installation, and I found some valuable PPF installation tips
    on the Mum Sports website. Their step-by-step guides and product recommendations made the process much smoother.

  2. Kyle Linel says:

    I love pasta, so when I learned about Barilla Rigatoni, I was thrilled. My friend would often make this delicious pasta when I was visiting him. And now he finally let me in on the secret of what they are called. So I want to share with you this best discovery for me. Try this great pasta yourself and you won’t regret it. Follow the link and learn more about the composition of these.

  3. soto ca says:

    lolololololol

  4. Vegendo says:

    Useful blog. Players in geometry dash meltdown may make their own levels and publish them online. You may play levels made by other users as well.

  5. Ingvar12 says:

    Corporate gifting is often a complex process that requires careful consideration of quality, appropriateness, and branding. In this context, Bohemia Crystal offers a line of products that hit all the right notes. From elegant vases to sophisticated barware, these items are suitable for a wide range of professional relationships and occasions. You can examine the offerings in more detail at https://northamericancrystal.com/manufacturers/brand-bohemia-crystal . By opting for such finely crafted gifts, you send a clear message about your commitment to excellence and your appreciation for meaningful connections.

  6. Ingvar13 says:

    Corporate gifting is often a complex process that requires careful consideration of quality, appropriateness, and branding. In this context, Bohemia Crystal offers a line of products that hit all the right notes. From elegant vases to sophisticated barware, these items are suitable for a wide range of professional relationships and occasions. You can examine the offerings in more detail at https://northamericancrystal.com/manufacturers/brand-bohemia-crystal . By opting for such finely crafted gifts, you send a clear message about your commitment to excellence.

  7. akinava says:

    Modern technologies can improve your production or automate warehouse management. All this, first of all, allows us to reduce the share of manual labor in the company, as well as increase and maintain productivity at a stable level. I recommend starting with articles like this one https://deusrobotics.com/the-role-of-lidar-in-agv-navigation/ and also learning more about solutions provided by companies like deusrobotics.

  8. Michealjackson says:

    Protect your journey to Canada with 미국 여행자 보험 가격
    from Stone Well Financial. They prioritize your safety.

  9. Lipstoik says:

    Still haven’t chosen a reliable online casino in Britain? I realise it can be a bit tricky but I have managed to choose a really good online casino site. I advise you to read more about the casino Sun Vegas and register. For registration you will get bonuses and you can play the best slot machines. Here you will definitely get bright emotions and you can win real money and withdraw them to your bank card

  10. Jake Brewer says:

    Looking for short term broadband solutions? Moving Internet has you covered. I recently used their services during a short-term rental, and the reliability and speed were outstanding. Definitely worth considering for temporary internet needs.

  11. Solar says:

    I appreciate the content in this blog. Thank you!

Leave a Reply

Your email address will not be published. Required fields are marked *

Current month ye@r day *